Within the Forge Worlds of Ancient Terra, are the mightiest War Machines constructed. Within the Forge Worlds of the Eye of Terror, are the mightiest War Machines defiled. What once was pure adamantium, now becomes twisted and deformed. The Servo-Arm of a Techmarine, it's purpose now distorted. From deep within the Foundries, a Chaos Dreadnought is born - anew. From head to toe, it's armoured form now serves the Chaos Powers:
When it comes to customising your models for 40K, I feel that there is no better army than that of Chaos and it's Chaos Space Marines - as within reason (or not!), anything goes ... As such, this is my first outing into those Dreadnoughts of the Forge World range. At first, I was concerned about constructing this Dreadnought model (because it's made of resin). I initially found the resin somewhat stranger to work with - as I'd only assembled both plastic and metal kits (before). After worrying about resins health and safety (e.g. your not supposed to breath it in), I decided to assemble the kit outdoors (e.g. to reduce the chance of that). I remember that the parts required considerably more cleaning than a typical plastic model kit - with a set of modelling files being the order of the day. Now, I started to paint this model in my old Iron Warriors paint scheme: pure bolt-gun over Chaos black undercoat (with no dry brushing). It was then to the burnished gold (for the raised armour edges) - followed by a brake, for several years! I was simply unconvinced by my old Iron Warriors paint scheme (at least it's ability to make a Dreadnought look good). Three weeks ago did my repaint start - but this time I dry-brushed the bolt-gun over Chaos black. I'm so glad that I did! I immediately had a new goal - to finish my Forge World Chaos Dreadnought to the highest quality, that I could. One of the hardest parts of the repaint was the Iron Warriors markings (the black and yellow bands). Whilst I used my usual technique for painting these (i.e. painting them straight on), I found it somewhat harder. The two markings on the top were restricted by the non-square burnished gold borders, together with two sunken-slots (in the top face) that made it easier for the yellow paint to run. The lone marking on the bottom, was complicated by the curved surface and awkwardness of brush angle (as was required to clear the sarcophagus). It was then onto the skulls - which required more attention (especially the large skull where the twin-linked Lascannon emerges). This required a slight modification to my usual approach to skull painting. Whilst I still used an ushabti bone base, together with a watery mix of tuskgor fur and gehenna's gold (applied to the top), I decided to add some dry-brushed burnished gold as an extra step (as I found that this helped to bring the details out). I also felt that I was akin to an Iron Warrior myself - with the addition of an extra painting step! Once the standard painting had been finished (such as the Dark Angels green, power chords/hoses) - it was onto the rivets. At this point did I dilemma: Should I paint each individual rivet? My reason for the dilemma? There's quite a few rivets on this Dreadnought model ... Fortunately, I decided that I would - and have found myself extremely pleased with the results! In particular, I love the way that the red rivets contrast with the burnished gold. Are you afraid of painting rivets? Well, dip the end of a cocktail stick into your paint, then dab the end onto a rivet! As for the Dreadnoughts weapons? Well, Forge World tends to offer you quite a selection for a Chaos Dreadnought (such as Plasma Cannon, Lascannon, Multi-Melta, Autocannons, Heavy Bolters, etc.). Whilst it took a while to decide (e.g. you have to pick the right ones for your Dreadnought body), I eventually opted for a twin-linked Lascannon (for powerful hits against enemy vehicles), together with a Chainfist (for it's ability to cut through the armour of enemy tanks). Overall: I enjoyed the challenges involved with assembling this model - which, for the most part, came from the fact that it's made of resin. With the Will of the Emperor, did I overcome these challenges - and I was soon within the familiar Realms of Chaos black undercoat, and burnished gold raised armour edges! This is my favourite Iron Warriors Dreadnought (to date) - and I know that it is Pride of Place within my Iron Warriors army. If I could name one thing to make my Chaos Dreadnought better? It's that I could have placed the model on a Dreadnought scenic base.
| Victorian HawkPermalink